Solid-state-logic Duality 82S6DUA20C Manual do Utilizador Página 29
- Página / 127
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Having selected a channel, or range of channels, all the functions in the area above can be
selected/deselected. Routing buttons 1-24 and MIX A, MIX B, MIX C, are self explanatory, as should most of
the buttons above. Note that changes made to the ‘PROCESSING ORDER’ are graphically indicated on the
channel TFT displays.
Items that may not be immediately obvious are as follows:
+48V – phantom power may only be selected here, as can INPUT FLIP and the channel input source –
‘CHANNEL IN’.
SOLO ISOLATE – Solo isolated channels will not be cut when other channels are soloed. Useful for FX
returns.
In the ‘PAN MODE’ section, INC ROUTE works in conjunction with the channel SELECT and TO functions, and
provides incremental bus routing for a range of channels. The selected channels will be incrementally routed
(or derouted if currently assigned) to consecutive busses starting from the first bus selected. 5.1 PAN enables
5.1 panning mode. PAN TO TRK routes the output of the selected channel’s pan to the Track busses. Stereo
panning is between odd/even pairs; 5.1 panning divides the track busses into four 6-channel groups. EFX TO
TRK replaces the channel feed to the Track busses with the active EFX send output. Stereo Cue EFX sends
are automatically routed to odd/ even pairs.
When SET AUX is selected, changes made to Cue Stereo and FX source and destination routing and On/Off
state, on any of the selected channels, will be copied to all selected channels, allowing the quick set up of aux
sends. Again, if some functions are on and some are off on the selected channels, the lowest numbered
channel in the selection sets the initial state.
SET and CLEAR provide an alternative way to set up routing. Press either SET or CLEAR, then select the
function(s) you wish to turn on or off. Pressing the select button on any channel will set or clear the selected
function(s).
Pressing ALL when SET or CLEAR are selected will make the SET or CLEAR button flash. A second press on
SET or CLEAR will make the assignment/de-assignment across all channels.
UNDO undoes all changes since the routing panel was last made active. As a safety measure, it requires two
presses to carry out the undo operation. On the first press, the UNDO button will flash, and a second press will
cancel all routing and channel settings that have changed since the routing panel was first selected. To cancel
and undo, deselect the routing panel by pressing the + and - buttons while the UNDO button is flashing.
Central Routing Panel
2-17
Duality Operator’s Manual
- Operator’s Manual 1
- Solid State Logic 2
- Table of Contents 8
- TTOOCC--66 8
- Section 1 – Introduction 9
- Exceptional Signal Processing 10
- Creative Versatility 10
- DAW Controller 11
- Controller Features Summary 11
- System Options 11
- About this manual 12
- Contacting Solid State Logic 12
- Overview 13
- An Introduction to Split Mode 14
- Routing and Signal Flow 14
- Channel Strip 15
- Channel Input Section 16
- Dynamics Section 17
- Equaliser 19
- Channel Output (CHOP) 20
- Signal Processor Routing 20
- Channel Sends 21
- Split Mode 22
- Channel Pan 22
- D-pot and DAW Control 23
- Channel Cut and Solo 23
- Channel Fader 23
- Fader Grouping 24
- The Channel TFT Screen 24
- Channel Processing Order 25
- Channel Metering 25
- DAW Status Indicators 25
- Console Operator’s Guide 26
- Duality Operator’s Manual 26
- The Centre Section 27
- Central Routing Panel 28
- Main Output Functions 30
- Main Bus Compressor 31
- Master Fader 32
- Track Bus Master Controls 33
- Monitoring 34
- External Source Selectors 35
- Monitor Insert 36
- Monitor Metering 36
- Monitor Options 37
- Bass Management 37
- Monitor Level Calibration 39
- SOLO / AFL / PFL 40
- Cue/FX Send Master Controls 41
- Stereo Return Channels 42
- Misc Options 43
- Communications 44
- Oscillator 45
- Mix Reassign Matrix 46
- LFE Channel 46
- Stereo Mix Matrix 46
- Group Control Faders 47
- Centre Section Metering 48
- Setup Menu 49
- DAW Control 50
- Section 3 – DAW Control Guide 51
- Console Focus 53
- Channel Banking Controls (6) 53
- DAW Window Buttons (13) 54
- DAW Utility Buttons (9) 54
- Modifier Buttons (10) 55
- The Default Button (7) 55
- Channel Functions 56
- Channel Solo and Cut Panels 57
- Record Ready Mode 58
- Edit Mode 58
- Select Mode 59
- Setting Sends Pre/Post Fader 60
- Muting a Send Output 60
- Motion Control 62
- Other useful transport modes 63
- Footswitch Control 64
- Numeric Keypad (18) 66
- Plug-In Editor 67
- Plug-In Display Modes 68
- Selecting a Plug-In to Edit 69
- Changing Plug-in Parameters 69
- Comparing Your Changes 70
- Bypassing Plug-ins 70
- D-pot Sensitivity 70
- Soft Keys 71
- Edit Tools Menu 72
- Edit Modes Menu 72
- Status/Group Menu 72
- Function Keys 73
- EDIT Menu 73
- SSL Menu 73
- Working with DAW Automation 74
- Automation Status Display 75
- Suspending Automation 75
- Automating Cuts 76
- Automating Pans and Sends 76
- Automating Plug-Ins 76
- Implementation 77
- Push to Flip 78
- The Logic Template 79
- CYCLE DROP REPLACE CLICK SOLO 80
- Nuendo/Cubase Template 82
- LEFT RIGHT CYCLE PUNCH 83
- PREV ADD NEXT 83
- The Sonar Template 85
- Digital Performer Template 88
- DAW Control GuidE 90
- Section 4 – Total Recall 91
- Total Recall and Projects 92
- Saving a TR Setup 93
- Recalling a TR Setup 94
- Deleting a TR Setup 94
- Renaming TR Setups 94
- Total Recall Displays 95
- Resetting soft switches 96
- OOvveerrvviieeww 97
- Project 1 Title 1 — selected 99
- Project 2 Title 2 99
- OOppeerraattiioonn 100
- Mix Enabled 101
- Project 16 :: Title 1 101
- 00 : 02 : 12 : 23 102
- Mix Review 104
- Mix Running 104
- DDiissccaarrdd 105
- TTrriimm 106
- TTrriimm LLoocckk 107
- MMoottoorrss OOffff 108
- SSnnaapp MMooddee 108
- AAuuttooTTaakkeeoovveerr 108
- CUT UNCUT 109
- UT UNCUT 109
- CCooppyy aanndd SSwwaapp 110
- FFaaddeerr LLiinnkkss 111
- Introduction 117
- Setting a Fixed IP Address 118
- Connecting to Duality 119
- Project Tab 120
- Backing up a Project 121
- Restoring a Project 121
- Notes Tab 121
- Channel Tabs 122
- Total Recall 124
- Exts Names 125
- Misc Tab 126
- Operator's 127
Manuais e produtos relacionados com Áudio Solid-state-logic Duality 82S6DUA20C
Áudio Solid-state-logic AWS V4 Manual do Utilizador
(45 páginas)
(45 páginas)
Elo Touch Solution E317038 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Monitory z ekranem dotykowym Elo Touch Solution E317038.
Dostarczamy 1 pdf podręczników Elo Touch Solution E317038 do pobrania za darmo według typów dokumentów: Arkusz Danych
Comentários a estes Manuais